Universal insulation cover caps from Hellermann Tyton that allow thermal insulation to be placed over downlights. Available in three sizes, the Spot Clip is made from Polyamide 6.6 and is suitable for use in plasterboard ceilings. This is a cost effective way of having continuous loft insulation over a downlight installation and complying with UK Building Regulations for Part L (energy efficiency).
Specification
- Available in 3 sizes, see dimensions tab for each size.
- Spot Clips 1 and 2 are suitable for downlight hole diameters of 62-90mm. Or for larger sizes the Spot Clip 3 can be used with hole sizes of up to 160mm.
- Material: Polyamide 6.6, fiberglass reinforced.
- Operating temperature: -20 to +120 degrees C.
- Approved to: EN60659-2-12 / Glow Wire Test 960 degrees C.
- Can be retrofitted from the room below.
- Manufacturer: Hellermann Tyton
The SpotClip range is expanding with many more sizes now available. Here is a link to the SpotClip web page. Please contact us for prices for any other sizes.
just the job for what i required and a very good price
Great to provide a gap / air space where there is loft insulation in place over the lamp.
Did the job at a great price
Good product. Does the job effectively and economically
A bit fiddly and costly but did the job well. Not aware of any other products available at this price.
Spot Clip 1
- Hole diameter: 62-90mm
- H (see drawing below): 90mm
- H2 (see drawing below): 82mm
- For maximum downlight heights of 70mm.
- 4 leg design.
Spot Clip 2
- Hole diameter: 62-90mm
- H (see drawing below): 117mm
- H2 (see drawing below): 115mm
- For maximum downlight heights of 95mm.
- 4 leg design.
Spot Clip 3
- Hole diameter: 65-160mm
- H (see drawing below): 123-160mm depending on positioning of legs.
- H2 (see drawing below): 120-160mm depending on positioning of legs.
- For maximum downlight heights of 130mm.
- 3 leg design.
- Spot Clip 1 & 2: CLICK HERE
- Spot Clip 3: CLICK HERE
Spot Clip Insulation Cover Caps (Various Sizes)RRP: £3.39 Prices FromEx VAT £3.05 Inc VAT £3.66 10% off RRP |
Insulation Cover Guard Ansell EdgeRRP: £1.50 Prices FromEx VAT £0.38 Inc VAT £0.46 74% off RRP |
Insulation Cover Guard For Click Inceptor Nano & Pico FGRRP: £1.76 Prices FromEx VAT £0.62 Inc VAT £0.74 65% off RRP |
|
| Short Description |
Universal insulation cover caps from Hellerman Tyton that allow thermal insulation to be placed over downlights. Available in three sizes, the Spot Clip is made from Polyamide 6.6 and is suitable for use in plasterboard ceilings. |
Insulation cover guard for use with the Ansell Edge fire rated GU10 downlights. Available in 2 variations; 1 for the fixed and IP65 version and another for the adjustable version. These insulation supports allow the Ansell Edge to be covered with thermal insulation. |
Insulation cover guard that allows the Click Inceptor Nano downlight to be covered with thermal insulation. This cost effective accessory converts the Click Nano into an insulation coverable downlight.
|
| SKU |
SPOTCLIP***
|
AEFRIS*
|
ISC1020
|
| Manufacturer |
Hellermann Tyton
|
Ansell
|
Click Scolmore
|
| Dimmable |
N/A
|
-
|
No
|
| Voltage |
N/A
|
N/A
|
N/A
|
| Beam Angle |
N/A
|
-
|
No
|
| Cap Type |
N/A
|
-
|
No
|
| Depth / Height |
N/A
|
N/A
|
N/A
|
| Cut Out Size (varies: check downlight dimensions) |
N/A
|
-
|
No
|
| Luminous Flux |
N/A
|
-
|
No
|
| Wattage |
N/A
|
-
|
No
|
| Fire Rated |
N/A
|
N/A
|
N/A
|